Brain / iKon / Xbar / TracX 3.2.000
Device: iOS Universal
Category: Entertainment
Price: $9.99, Version: 3.1.027 -> 3.2.000 (iTunes)
Description:App for iOS tablets and phones. It allows to set parameters and settings on Brain/Ikon/Xbar/Tracx flybarless controllers.
This App needs latest firmware release on the unit to be used to its full potential. If your devices has internet access, the app will prompt you in case a new firmware for the flybarless unit is available.
App is supported natively by Flybarless units with code MSH51630 and MSH51632, all other units type need BT module MSH51610, sold separately.
MSH products can be purchased in any of the official MSH dealer shop.
What's New
- 3.2.000 (firmware 3.2.000)
• Added management of the telemetry of new YGE *VT ESC's
• Implemented the changed (from Kontronik before the imminent release) Kontronik ESC protocol
• Added for Nitro/Gasser, the management of telemetry log and transmission of a digital temperature sensor (Jeti: MT300EX, Futaba: SBS-01T) with sensor signal connected on CH5 and powered from an "Y". Work for ALL protocol selected (with Futaba S.Bus2 receivers the Futaba temperature sensor can be directly connected on the S.Bus2)
• Added Multiplex MSP telemetry. Now on Multiplex transmitters can be displayed: “Main Battery Voltage”, “Main battery instantaneous current”, “Main Rotor RPM”, “ESC Temperature”, “Temperature 2”, “Main Battery used mAh” (Protocol selection icon and connection schematics updated)
• Added with Dial regulation, the possibility to change the value of "mAh Max Discharge" (that cause a reduction of 20% of RPM) parameter by a transmitter channel (can be used a three positions switch for three different variations), other than with "Integrations"
• Now it is possible to operate the Units on Flybarred models with a simple click (anyway useful for: Tail Gyro, Governor, Auto Level, Rescue, Timers, Logs of internal data's, Vibrations, Events, Esc Logs, Telemetry, Transmitters Integrations, Dials for fine setup, all kind of receivers decoding, CCPM mixer, Smartphone setup, etc.)
• Added the new loggable values "Bailout Timer" and Temperature1 F° and Temperature2 F° (Fahrenheit) to the already present Temperature1 C° and Temperature2 C° (Celsius), in Windows, Android, iOS apps and in Spektrum, Graupner and Jeti integrations. Now the loggable parameters are 39
• Added 9 new Events: "Logs Recording Started", "Voltage <= 4V3", "Bailout Timer ended", "Watchdog Reset", "Resetted to Factory defaults", "Throttle gone in Fail Safe", "Aileron output limit reached", "Elevator output limit reached", "Logs memory was erased". Now the Events kinds are 38
• Changed "Wrong accels values" Event description to "Unit not level at startup. Check unit orientation" and other little revision of Event names
• Changed name of SRXL Fades to Rx Fades, and now Rx Fades, Frame Losses and Holds are elaborated and can be logged for all the serial selected protocols (but not for "Standard PWM Receiver")
• Changed all "Autorotation Timer...." occurrences to "Bailout Timer..." in Events, Logs, Menu, of windows, Android, iOS, and Spektrum, Graupner, Jeti integrations
• Changed loggable parameters names from "SwashAileron" to "AileronOut" and SwashElevator" to "ElevatorOut"
• Now on all telemetry (Spektrum, Futaba, Jeti, Graupner, Multiplex, *FrSky*) for RPM if any RPM sensor is connected to the GOV connector, the RPM read from ESC is sent (if a telemetric ESC is connected, otherwise zero is displayed)
• Now the receiver Fail Safe channels signal is recognized and logged also for FrSky and SUMD receivers other than for Futaba and SRXL receivers
• Revised page 3 instructions "Receiver Selection" explaining that also Graupner "SUMO" can be received, also Spektrum "PPM" can be received (EG: AR7700), also Spektrum "REMOTE RX" can be received (EG: AR7700) and that with "oldest Spektrum receivers" (EG: AR9020, AR7700) the unidirectional SRXL can be used, and that with older Spektrum receivers the bind must be manually done with a bind plug on the receiver as usual
• In wizard page3 instructions, under "Hott/SUMD/UDI/Xbus-B/Mpx-SRXL, instead of (no Spektrum) corrected to (oldest Spektrum RX)
• Added in the panel 3 instructions "Receiver Selection" the "FrSky" paragraph
• New FrSky schematics where is clearer that the MSH51645 accessory is not an option but a requirement
• In wizard page 6 revised the position of swashplates icons
[MORE]
Brain / iKon / Xbar / TracX